International Shipping
Please Read!
International Shipping
|
||
|
|
|
|
Roku Brightsign HD410 & HD810 & HD1010 Interface Products |
||
Use this link for: DMX512 & RGBW (Red-Blue-Green-White 15 ampere driver) Interface boardsUse this link for: RS232 Serial Products |
||
Product |
Description |
Picture
|
ROKU-C-16Price Each: $145.95 (USD) This board utilizes both the GPIO port and the 5VTTL Serial Port. The 5V TTL Roku serial port is used to control the two output ports and read the inputs 8-16 (Buttons 8-15) |
16 Inputs (Buttons) and 16 Outputs w/Lamp Drivers
External 12V Power required Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables Serial Example 'CSV' BrightAuthor Link http://forums.roku.com/viewtopic.php?f=19&t=31022 Links: DB15 Cables TTL Example 'TTL_16.BRS' (Bright Script) |
Comes with .9 meter Stereo Cable for '5V TTL' serial port. |
DB15_TB10_3VPrice Each: $17.25 |
DB15 Adapter This adapter board mounts to the
back of the Brightsign (directly plugs into the Brightsign connector) and the 8
GPIO's are available using the
Terminal Block provided. It can also be remote mounted by using a DB15 cable.
3.3 volts available on Terminal Block. Now with attaching screws. Use for
simple Push-Buttons Switches (no lights).
Links: DB15 Cables Schematic (Typical Connections) |
|
Sync_Board
|
This sync-board mounts to the
back of the Brightsign (directly plugs into the Brightsign 15 pin connector)
with attaching hardware. Use for 'sync' of multiple BrightSign players
(eliminates custom sync cable). 4 inputs (Buttons) and 4 drivers (Outputs) Links: Specification Sheet Schematic (Typical Connections) |
|
|
HD_4OPTO Price Each: $25.25 |
4 ISOLATED INPUTS (Buttons) for remote trigger of the BrightSign (12V
or 24V remote trigger voltage). !No Outputs! Direct mount to
DB15 connector on the BrightSign (attaching hardware included) Links: Specification Sheet Schematic (Typical Connections) |
|
Roku_HD_4x4Price Each $45.50 |
I/O Interface (4 inputs (Buttons) and 4 Light Driver outputs),
External power required to drive Lamps/LED's
Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables |
|
Roku_HD_GPIOPrice Each $89.50 |
Special Interface (4 inputs (Buttons) and 4 outputs or 5 inputs and 1
of 5 outputs) Microprocessor Controlled.
Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables |
|
Roku_HD_DMX (Roku_HD_485)Price Each $133.50 |
Special Interface (4 inputs (buttons) and 4 outputs) Microprocessor Controller +DMX512
Controller + PIR
Jack
Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables About DMX512 |
|
ROKU_C_TTL_8x88 Inputs (Buttons) and 8 Outputs Price Each $115.00 |
This board utilizes the 5V TTL serial port. All 8 outputs are controlled using a single data byte to the TTL port. New CSV command TTLSend()! Links: Schematic Specifications Sheet Power Supplies BrightAuthor Link http://forums.roku.com/viewtopic.php?f=19&t=31022 Links: DB15 Cables |
Comes with .9 meter Stereo Cable for '5V TTL' serial port. |
|
ROKU_C_TTL_8x168 inputs (Buttons) and 16 outputs Price Each $125.50 |
This board utilizes the 5V TTL serial port. All 16 outputs are controlled using two data bytes to the TTL port Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables |
Comes with .9 meter Stereo Cable for '5V TTL' serial port. |
ROKU_HD_Hybrid (ROKU_HD_8X8 Board)Price Each: $125.50 (USD) This board utilizes both the GPIO port and the RS232 Serial Port. The serial port is used to control the lamp/relay drivers. Optional connector for PIR (Passive InfraRed Detector) |
8 Inputs (Buttons) and 8 Output w/Lamp Drivers
External Power (6 -24 volts) required for lamps Links: Schematic Specifications Sheet Links: DB15 Cables DB9 Cables Serial Example |
|
ROKU_C_RFIDRadio Frequency IDentification Interface Price Each $125.00 |
RFID (Radio Frequency IDentification) Interface This board utilizes the 5V TTL serial port. Transponder Adapter Modules Required! Contact HMS Technical for availability. External 12 volts required Links: Schematic Specifications Sheet Power Supplies Links: DB15 Cables |
Comes with .9 meter Stereo Cable for '5V TTL' serial port. |
RFID_PAMRFID 'Pico Adapter Module' Price Each $55.00 |
RFID Pico Adapter Module (For use with RFID boards) The Pico Module (NOT SUPPLIED) will mount to this board with a 12 pin header (header supplied with this board). The header will have to be soldered to the Pico Module. Links: Schematic
Specifications Sheet
|
Comes with 12 pin header to solder to the 'Pico' RF Module |
HC-DRIVER-8 High Current Adapter BoardPrice Each $88.95 |
Connect to any 'HMS Output Port' to this board to expand the
output current drive to 6 amps per output.
Links: Specification Sheet Schematic |
|
8-Out-Ser-6A (Closeout) 8 Channel High Current PWM Driver Board
120 Channel Light System
|
Use the 5V TTL (serial) port of the BrightSign to control up
to 120 channels of 12 volt lighting. 8 channels per board, 6 AMPS per channel up to
18 amps total (per board). Brightness and fade control of all
120 channels. Modified to Rev3 Firmware (synchronized processors and
'scene play'). Note: Specification sheet is for this increased
current of the Rev3 board, otherwise this board works the same.
Links: Specification Sheet
Schematic RG174
Cables 'Y' Adapters |
|
8-Out-Ser
|
Use the 5V TTL (serial) port of the BrightSign to control up
to 120 channels of 12/24 volt lighting. 8 channels per board,
15 AMPS per channel up to 75 amps total (per board). Brightness and fade control of all
120 channels.
Links: Specification Sheet
Schematic RG174
Cables 'Y' Adapters |
|
Scene-Controller
|
Use this board with 8-Out-Ser boards to synchronize
'Scenes'. 4 outputs 'Y' type for multiple 8-Out-Ser boards.
Links: Specification Sheet Schematic |
Comes with .9 meter Stereo Cable for '5V TTL' Serial Port |
|
HD_64X64 I/O Board Price Each $145.95 |
Inputs: Uses a switch Matrix scheme (see schematic page 2)
to decode 1 of 64 switch inputs (buttons).
Outputs: Turn on 1 of 64 outputs, or any combination of outputs selected if Option 1. |
Comes with .9 meter Stereo Cable for '5V TTL' serial port. |
|
HD-4X4R I/O Board 4 INPUTS (Buttons), 4 ISOLATED OUTPUTS (RELAYS) Price Each $74.95 |
Inputs: 4 direct inputs to the BrightSign (normally open
switches)
Outputs: Relays for isolated outputs. U.L. Contact Ratings: 30VDC/1.0A, 100VDC/0.3A, 125VAC/0.5A, 125VAC/1.0A Links: Specification Sheet Schematic Power Supplies Note: 12V Power Supply Required (300milliamps or better) |
|
|
HD-4OPTO-4R I/O Board 4 ISOLATED INPUTS (Buttons), 4 ISOLATED OUTPUTS Price Each $99.95 |
Inputs: OPTO-ISOLATORs (similar to solid state relays) for
inputs + 3 direct inputs to bypass opto-isolators if needed (12V or 24V
input voltages)
Outputs: Relays for isolated outputs. U.L. Contact Ratings: 30VDC/1.0A, 100VDC/0.3A, 125VAC/0.5A, 125VAC/1.0A |
|
3 button BoxPrice Each: $51.00 |
3 Lighted Switches (Lights are controlled by the Brightsign)
Links: Schematic Specifications Sheet Links: DB15 Cables BrightAuthor (how to set lights) |
|
4 Button BoxPrice Each: $55.00 |
4 Lighted Switches (Lights are controlled by the Brightsign
Links: Schematic Specifications Sheet Links: DB15 Cables BrightAuthor (how to set lights) |
|
5 Button BoxPrice Each: $71.00 |
5 Lighted Switches w/microcontroller and 1 of 5 Light
selection controlled by the Brightsign.
Links: Schematic Specifications Sheet Links: DB15 Cables BrightAuthor (how to set lights) |
 |
Medium Enclosure, ABS Plastic, AlmondEN-31-A Price Each $15.04 |
Enclosure for most small and medium sized HMS boards (see Product
Selector for compatibility)
Maximum Board Size of 4.1L x 4.8W 'inches' (1.25 inches high) Note: Removable End Plates, Not Machined (No Cutouts) |
|
Large Enclosure, ABS Plastic, AlmondEN-42-A Price Each 19.25 | Enclosure for larger HMS boards (see Product
Selector for compatibility)
Maximum Board Size of 6.5L x 4.8W 'inches' (1.25 inches high) Note: Removable End Plates, Not Machined (No Cutouts) |
|
Links Developer Tools
RS232-TTL Adapter
Power Supplies & Switches (Buttons)
Cables Audio
| ||
Note: There are other 'non production' items available. such as a Triac daughter board for controlling kiosk lighting. There is also a GPIO board with the triac circuit built in. No requests to date so the board is on hand, just not setup. The serial port of the Brightsign can be used for any number of features. I.E. Any number of inputs, Any number of Lamp drivers and DMX-512 controlling or 120VAC control of lighting.
Please inquire if you have a custom requirement for interfacing! Turn around can be a little as two weeks.
| Note: External Supply Voltage: An External Power Supply is needed to power the loads on the output connector. Do not connect any loads that have their own power that exceeds the power as applied to the board using the 'Ext. Power Connector'. Doing so may result in damage to the board. I.E. Suppose that 12 volts is supplied to this board and you have a relay board with it's own power of 24Volts DC that powers the relays. The 24VDC will feed back into the board via the foldback diodes. Note: Foldback diodes are required for inductive loads such as relays or small motors. |
Author: Richard Harkey
Copyright © 2009 HMS Electronics. All rights reserved.
Revised: January 27, 2012
